The control, performance and efficiency of energy usage in industrial, commercial and public buildings.
This occupation is found in the building services sector. Building Energy Management Systems are implemented in buildings with mechanical, HVAC (heating, ventilation and air conditioning) and electrical systems to enable energy efficient control of the internal environment. The buildings themselves can vary widely in size and function.
The broad purpose of the occupation is clearly focused upon the control, performance and efficiency of energy usage and comfort control in industrial/ commercial /public buildings of a diverse nature. It requires an associated understanding of these environments and the balance between cost, comfort, safety, health and wellbeing. It includes the specialist design, installation and commissioning expertise required to undertake this control and servicing function.
Typically a BEMS Controls Engineer will be involved initially with designing the building energy management system that controls the building services (e.g. heating, air conditioning, renewables).They may also write related software and graphics as well as installing and commissioning such systems. Another key area is connecting and integrating with other building systems (e.g. security) to create ‘Smart Buildings’. After the building is occupied and being used they may also be involved in servicing & maintenance, fault finding if there are problems with the system and energy performance reviews.
Within the role the following skill set will be needed to cater for the range of different BEMS types:
1) Controls Hardware and Logic: Engineers will be required to select, install, configure and update control hardware platforms from the main manufacturers in the UK Market.
As well as manufacturer specific control hardware, engineers will also require generic knowledge. Particularly important is an understanding of controls principles such as logic, proportional and integral control and energy saving techniques for control strategy efficiency.
2) Field Devices: Field devices are manufactured by numerous organisations but can be, broadly speaking, categorised into Sensors, Valves, Actuators, Dampers, Variable Speed Drives, Switches and relays. The engineers will understand the controls and performance of field device types from first principles.
3) Networking: Standard network architectures such TCI/IP, MSTP and RS485 are the main stays of the industry so engineers will be required to design, install, maintain and fault find these types of networks along with more specialist sub-networks for integration of items like utility meters.
4) Communication Protocols: The engineers will be trained to a high level in the common open standard protocols in widespread use within the BEMS industry with the most common being BACNet.
5) Supervisor Software: Interaction with a BEMS is typically conducted via a ‘software supervisor’. This is, generically, a graphics based software platform aimed at providing an intuitive way for the user to find their way around their system. The engineers will be required to have a knowledge of the construction of graphics, creation of user accounts, alarm management and schedule management.
Mainstream environments/considerations for the use of these skill sets include:
In their daily work, an employee in this occupation interacts with a wide range of building stakeholders (e.g. owners/operators/facilities management/occupiers) in both the private and public sector. They would need to successfully liaise with both external and internal functions of their own organisation but also those of clients/key influencers (e.g. contractors/local councils/consultants) to ensure that different stakeholder needs are taken account of within the client’s controls specification.
Employees will be both office and site based.
An employee in this occupation will be responsible for the delivery and performance of the BEMS and to achieve this they will have to manage budgets and teams of people, which could vary depending on the size of the business. The BEMS industry is made up of a wide range of organisation types/sizes but there are a significant number of SME’s (small/medium enterprises). Therefore employees will need to be able to work alone and under supervision.
| Duty | KSBs |
|---|---|
|
Duty 1 Design and create BEMS Technical Documentation |
|
|
Duty 2 Create wiring schedule and power loadings for panel manufacture |
|
|
Duty 3 Adhere to safe working practices to ensure the BEMS elements of the electrical systems are safe to use |
|
|
Duty 4 Create Health & Safety documentation such as Risk Assessments and Method Statements (RAMS) |
|
|
Duty 5 Design and write software for control systems to an industry approved standard |
|
|
Duty 6 Design and create client approved user interface for plant and systems with appropriate reference to integration issues |
|
|
Duty 7 Review completed control panel drawings to check, amend and approve |
|
|
Duty 8 Install BEMS control equipment and wiring systems |
|
|
Duty 9 Commission BEMS software and controls equipment |
K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 K13 K15 K16 |
|
Duty 10 Undertake a servicing and maintenance requirement of an existing BEMS installation |
|
|
Duty 11 Carry out fault finding and rectification of defective control equipment or software algorithms |
|
|
Duty 12 Carry out and produce detailed conditional site survey reports along with remedial/ enhancement recommendations |
|
|
Duty 13 Produce recommendations for enhancing energy performance |
|
|
Duty 14 Carry out the electrical testing and inspection of BEMS related controls equipment |
|
|
Duty 15 Create Operation and Maintenance documentation |
K1: Understanding building control technologies and theory including: The primary role and function of the control system The merits of automated control over manual control methods The development of interface protocols so data can be shared and exchanged between the BEMS and 3rd party systems e.g. access systems and lighting systems
Back to Duty
K2: Understand the fundamentals of controlling HVAC (heating, ventilation and air conditioning) and building technology
Back to Duty
K3: Understand hydrodynamics and hydronic systems in buildings e.g. the transfer of heat energy and cooling energy through a building using water
Back to Duty
K4: Understand thermodynamic relationships in air conditioning systems
Back to Duty
K5: Understand cooling systems, heat generation and renewable technology
Back to Duty
K6: Understand the principles and practices of measurement technology
Back to Duty
K7: Understand Control Panel wiring, construction and relay logic
Back to Duty
K8: Understand the control principles associated with the design, function, facilities management and use of the building
Back to Duty
K9: Understand communications technology protocols and media
Back to Duty
K10: Understand the practices and procedures for the installation of BEMS wiring systems
Back to Duty
K11: Understand the principles and practices for the commissioning of BEMS and associated equipment in buildings
Back to Duty
K12: Understand the principles for diagnosing and correcting faults in BEMS network systems and BEMS equipment in buildings
Back to Duty
K13: Understand the energy efficiency and comfort control requirement within buildings
Back to Duty
K14: Understand the testing, inspection and certification of BEMS related controls equipment
Back to Duty
K15: Understand the operation and application of BEMS field devices e.g. sensors
Back to Duty
K16: Understand relevant health & safety legislation and safe working practices applying to themselves and others. Give particular reference to understanding the requirements for protection of and safe working with electrical installations and BEMS impact on ‘wellbeing’
Back to Duty
K17: Understand the general characteristics of electrical installations and how to assess them
Back to Duty
K18: Understand the requirements of inspection and testing of BEMS element of electrical installations
Back to Duty
K19: Understand the principles of control logic including the fundamentals of proportional and integral control
Back to Duty
S1: Applying the control principles associated with the design, function and use of buildings e.g. to create points lists, description of operation, cable schedules
Back to Duty
S2: Incorporating hydrodynamics/ hydronic systems into designs
Back to Duty
S3: Applying the principles and practices of measurement technology
Back to Duty
S4: Incorporating cooling systems, heat generation and renewable technology into designs as applicable
Back to Duty
S5: Incorporating Control Panel wiring, construction and relay logic into the design process
Back to Duty
S6: Applying communications technology protocols and media e.g. MODBUS and BACNET
Back to Duty
S7: Applying relevant safety legislation, codes of practice and safe working practices to themselves and others
Back to Duty
S8: Identifying requirements for protection of electrical installations
Back to Duty
S9: Incorporating the needs of a variety of building stakeholders (e.g. owners/ operators) within the design of the BEMS system
Back to Duty
S10: Applying the practices and procedures for the installation of BEMS wiring systems
Back to Duty
S11: Interpreting the requirements for the BEMS element of electrical installations
Back to Duty
S12: Applying the principles and practices for the commissioning of BEMS systems and equipment in a variety of building types and environments
Back to Duty
S13: Applying the principles, for diagnosing and correcting faults in BEMS network systems and BEMS equipment
Back to Duty
S14: Applying the principles for completing conditional site surveys, along with associated recommendations
Back to Duty
S15: Applying knowledge of energy efficiency to optimise comfort in buildings whilst minimising energy usage
Back to Duty
S16: Identifying the requirements of inspection and testing of BEMS element of electrical installations within relevant legislative requirements, specifications, codes of practice and industry recognised practices
Back to Duty
S17: Carrying out the testing, inspection and certification of BEMS related controls and equipment
Back to Duty
S18: Applying the principles and practices for the design and commissioning of standard network architectures e.g. Ethernet TCP/IP, MSTP and RS48
Back to Duty
S19: Carrying out updates to BEMS system hardware to ensure compatibility with latest products
Back to Duty
B1: Be aware of the needs and concerns of others, especially in relation to diversity and equality
Back to Duty
B2: Create maintain, and enhance productive working relationships
Back to Duty
B3: Commit to compliance with health and safety
Back to Duty
B4: Strive to communicate effectively with work colleagues and clients using oral, written and electronic methods to communicate technical and other information
Back to Duty
B5: Take responsibility for working independently and completing work to the appropriate specifications and codes of practice
Back to Duty
B6: Solving problems within their own scope of responsibility, by applying technical and behavioural skills and knowledge to define the problem, identify, evaluate and select alternatives and implement solutions.
Back to Duty
B7: Accepting responsibility for their own work and actions and that of others in their team
Back to Duty
B8: Accepting, prioritizing, delegating and undertaking technical and other tasks effectively
Back to Duty
B9: Committed to working effectively with colleagues, the public, clients and other stakeholders
Back to Duty
B10: Take responsibility for personal development, demonstrating commitment to learning and self-improvement
Back to Duty
B11: Exercise responsibilities in an ethical manner
Back to Duty
B12: Undertake work in a way that contributes to sustainable development
Back to Duty
4
36
| Version | Change detail | Earliest start date | Latest start date |
|---|---|---|---|
| 1.0 | Approved for delivery | 03/02/2020 | Not set |
Crown copyright © 2024. You may re-use this information (not including logos) free of charge in any format or medium, under the terms of the Open Government Licence. Visit www.nationalarchives.gov.uk/doc/open-government-licence